How to control the temperature when using the thermal oil boiler diesel burner

Heat oil burner light oil burner, this is a special and common species, boiler diesel burner And the application is wide, so it is necessary to learn and understand, then, on this basis, then, is to explain the knowledge or solutions to some common problems for the heat transfer oil furnace and light oil burner, so that each has learning content People, in turn, can deepen their familiarity with this kind of heat conduction oil furnace, light oil burner, boiler and diesel burner. 1. How to deal with the sudden power failure of the light oil burner of the thermal oil furnace at high temperature? When the circulating oil pump cannot operate normally due to power failure, the heat transfer oil in the furnace tube will exceed the allowable value in a short time due to the residual heat in the furnace cavity. At this time, the cold oil delivery valve should be opened to release the cold oil in the expansion tank and send it to the oil storage tank. At the same time, the treatment of wet coal pressure fire or emergency shutdown needs to be completed within 5 minutes. In addition, we need to be careful not to drain the oil out of the expansion tank, otherwise the system will inhale air and cause problems. The oil level mark can be made on the level of the oil storage tank. When the cold oil is changed, the valve can be closed in time to avoid emptying the expansion tank and oil storage tank. 2. What determines the working temperature of heat transfer oil? Will the temperature difference affect the light oil burner of the thermal oil furnace? From a professional point of view, the working temperature of heat transfer oil is determined by the temperature required to heat the material in the heating device. Generally speaking, the temperature of the heat transfer oil in the light oil burner of the heat transfer oil furnace is required to be higher than the temperature of the heated material, and the larger the temperature difference, the smaller the heating area required. However, for some materials, problems can arise if they are at a high temperature. Therefore, the temperature difference will have an effect on the material, but for the heat transfer oil furnace and light oil burner, the effect is not great. 3. Are there requirements for the operators and users of the heat-conducting oil burner light oil burner? For the operators and users, there are some requirements for the heat-conducting oil burner light oil burner. The specific statement is: among the operators, some professional training is required, and the local boiler diesel burner safety supervision agency conducts inspection and certification. For users, it is necessary to formulate operating procedures for heat-conducting oil furnace light oil burners, and operators should operate boiler diesel burners in accordance with these operating procedures. Electric heating heat conduction oil furnace light oil burner is used for precise temperature control, and the temperature of the internal heat conduction oil can be understood through the automatic control system. It is used in our process, and sometimes it is found that the environment is equivalent to the heating effect under the conditions of heating and heat conduction When the oil temperature rises, the heat transfer oil needs to be heated to 400°C to reach 350°C, and later the heat transfer oil needs to be heated to a temperature of 500°C. Although this situation has an impact on the heating effect of the heat transfer oil heater, there are safety risks. The following analyzes the increase in the temperature difference of the light oil burner of the electric heating heat transfer oil furnace. As we all know, the material has a certain specific heat, and the required heat is different, but if you want to increase the thermal conductivity of 2ml of heat transfer oil and 2ml of oil, using 1 degree of heat is the same. From this point on, we can It is known that the heat-conducting oil heater used for external temperature control is accurate, and the heat-conducting oil heater used for external temperature control is realized through internal heat. When the total amount is constant, the temperature rises, and only one introduces the decrease of the heat-conducting oil flow. The decrease in the flow of heat transfer oil is indeed the main reason for the increase in temperature difference, which can be understood by repairing a large number of light oil burners in electric heating heat transfer oil furnaces. After using the boiler diesel burner for a period of time, it is necessary to test the hot oil product according to the relevant instructions. When a problem is found, it is necessary to replace the new heat transfer oil in time. It is important to prevent the heat transfer oil from oxidizing during use. It is important to note that the heat transfer oil exceeds 50°C. If it is exposed to air, oxidation will occur, which will cause the heat transfer oil to crack and the speed is very fast. Therefore, professionals are required to work normally When, close the auxiliary exhaust pipe to the upper exhaust valve. During use, the temperature difference between the inlet and the outlet will widen, which will destroy the previous design requirements, so that the heat transfer oil cannot be recycled, the thickness of the boundary layer will increase, and the thermal resistance will increase, which will increase the electric heating heat transfer oil. The reason for the increase in the temperature difference of the furnace light oil burner is found. The rest is how to solve the problem. This situation is generally caused by the blockage of the heat transfer oil pipe. The electric heating heat transfer oil heater is also introduced to you before cleaning. This problem can generally be solved after cleaning. . ! If you are interested in diesel combustion engines, please contact us for a quote!