Square box type coal-fired heat conduction oil boiler diesel burner

A higher working temperature can be obtained at a lower working pressure: ABD series heat transfer oil is used as a heating medium , The highest temperature can reach 350℃. Using silicone oil, the highest temperature can reach 400℃; when using molten salt, the highest temperature can reach 580℃; the actual working pressure is normal pressure, the highest working pressure is 0.6mpa, and the design pressure is 1MPa. Product introduction Heating furnace performance characteristics and technical parameters: 0~350℃ Working medium: heat transfer oil Working pressure: normal pressure Design pressure: 1MPa Heating capacity: 1800~14000kW (160~12 million kcal/hour) Product specifications: single heating Capacity: 160, 200, 250, 300, 350, 400, 500, 600, 700, 800, 900, 1000, 12 million CAL/hour Combustion method: chain grate Applicable fuel: bituminous coal Automatic control: mechanization, automatic combustion method Control, frequency conversion control, proportional adjustment, PLC programmable and touch screen control technology chain g furnace square box type coal-fired heat conduction oil furnace, light oil burner, heat conduction oil heating furnace Main features ★Save: It has the characteristics of high temperature and low pressure, reducing the pressure of thermal equipment Level, can reduce the investment cost of equipment. ★Energy saving: The use of closed-circuit forced circulation heating, without contact with the atmosphere, can prolong the service life of the heating medium, no emission, no pollution, low heat loss, maximum energy saving, low operating cost, and fast investment recovery. Environmental protection: no emissions, no pollution; ★Convenience: perfect operation control and operation safety monitoring device, simple operation, easy to use, safe and reliable operation; ★Wide surface: a wide range of applications to meet various high temperatures of various users The different use temperature of the heating production process, in line with the requirements of a variety of thermal equipment, can carry out precise temperature control and adjustment, stable use, uniform and useful heat exchange occasions, and the thermal efficiency can reach the best. ★Perfect: reasonable structure, novel appearance, complete supporting facilities, complete technology, good service, and no worries for users. Check before the operation process guide 1. Check whether the heating furnace and its surroundings are clean and free of debris, check whether the furnace body, burner, controller, fire hole and smoke pipe are normal; 2. Reverse the process equipment and process, and check the expansion tank Whether the oil level is higher than 1/4 to 1/2 of the liquid level, and whether the thermometer and pressure gauge are normal; 3. Turn on the power of the heating furnace control cabinet, check whether the voltage is normal, check whether the indicator light and all display instruments are normal; 4 .Adjust the gas main pressure reducing valve and the auxiliary pressure reducing valve to control the pressure to 0.005mpa. Start 1. Start the heat transfer oil circulating pump (according to the pump's operating rules, one transport oil, one preparation oil), after starting the pump, it will circulate normally for about 0.5 hours to stabilize the pressure; 2. Press the burner start button and observe the combustion Whether the flame in the furnace is burning normally. If there is no ignition, please start the burner again after troubleshooting. Operation 1. Normal shutdown (1) Gradually reduce the temperature, turn off the burner, and stop burning; (2) Wait for the hot oil temperature to drop below 70°C, and stop the operation of the hot oil circulating pump (refer to the pump operation steps); (3) Turn off the main power and make a shift record. 2. In an emergency, the burner should be quickly turned off and moved away along the hinge axis of the burner to form a natural ventilation state between the furnace and the chimney, so as to distribute the heat in the furnace to promote the natural cooling of the heat transfer oil and prevent overheat. Matters needing attention When checking the circuit, check whether there is any leakage around the light oil burner of the heat-conducting oil furnace. Sufficient oil and electrical fire-fighting equipment should be equipped nearby. Do not use water as a fire extinguishing agent. ! If you are interested in diesel combustion engines, please contact us for a quote!