Accident prevention for coal-fired heat transfer oil boiler diesel burner

When you use the coal-fired heat-conducting oil boiler diesel burner, you must also prevent coal-fired heat conduction from the equipment and media Occurrence of oil boiler diesel combustion engine accident. The second is to make the heat-conducting oil overheated in heat, not degenerate, and flow and transfer heat normally. Mainly include: 1. The coal-fired thermal oil boiler diesel burner used should be the qualified product of the national designated manufacturer. 2. The installation of the heating system of the coal-fired thermal oil boiler diesel combustion engine should be completed by the manufacturer or the designated installation unit, and the quality is qualified and meets the requirements. 3. The installation of the heating system of the coal-fired thermal oil boiler diesel combustion engine should be completed by the manufacturer or the designated installation unit, and the quality is qualified and meets the requirements. 4. The heat transfer oil supplier shall provide the physical and chemical performance data of the heat transfer oil and comply with national standards. The heat transfer oil should be tested once a year, and replaced or regenerated in time when problems are found. 5. The diesel burner of coal-fired thermal oil boiler shall fully discharge air, water vapor and light components during the start-up process. In operation, the heat transfer oil should maintain a high enough speed to prevent the pump from being cut off to avoid overheating coking or carbon deposition of the heat transfer oil. The filter should be cleaned regularly. 6. The safety devices of the diesel burner and heating system of the coal-fired heat-conducting oil boiler should be complete and intact. The over-temperature and over-voltage protection devices should be sensitive and reliable. Clean technology If your heat transfer oil boiler diesel burner is used for a long time or the selected heat transfer oil is not good or improperly used, coking and carbon deposits will block the pipes and heating surfaces, reduce heat transfer efficiency and increase energy consumption, and it will be difficult to meet Production demand. Heat transfer oil boiler diesel combustion engine oil carbon scale cleaning technology Heat transfer oil boiler diesel burner (heat medium boiler diesel burner) is a kind of organic heat transfer oil as heat transfer muon boiler diesel burner, for petroleum, chemical industry, printing and dyeing, food, etc. Safe and efficient, higher working temperature can be obtained under lower working pressure. Chemical fiber, plastics, coatings, building materials and other industrial enterprises quickly spread and use. Problems existing in the use of heat-conducting oil boiler diesel burner Problem 1: Condensation of heat-conducting oil easily makes the heat transfer area of ​​boiler diesel burner coking heat-conducting oil prone to thermal cracking and polymerization chemical reactions after high temperature heating, which reduces oil quality. For example, the heat transfer oil gel is thick, the carbon residue and acid value exceed the standard, and the coke crystals precipitate and deposit, causing the coking oil carbon scale in the heat transfer zone of the boiler diesel burner. Question 2: Coke fouling in the heat transfer area will increase energy consumption and cause fire accidents. The accumulation of oil coke fouling on the heat transfer tube wall of the heat transfer oil boiler diesel burner not only greatly reduces the heat transfer efficiency, increases the fuel cost, but also affects the downstream The temperature of the production process. Severely lead to overheating of the heat transfer wall, cracks in the pipe wall, corrosion and pipeline explosion, and major safety accidents such as fire and casualties caused by heat conduction oil leakage. Heat transfer oil is resistant to coke and anti-fouling. The deterioration of heat transfer oil accelerates carbon coking of boiler diesel burners. In the process of using heat transfer oil boiler diesel burners, the chemical components of heat transfer oil are prone to high-temperature oxidation, cracking decomposition and thermal condensation and other chemical reactions. Grease gelation. The coke particles produced by polycondensation greatly increase the carbon residual value of the heat transfer oil and form coke scale on the heat transfer surface. The scale of oil and carbon endangers the safe operation of boiler diesel burners. The carbon scale formed by the thermal oil product oil coke not only greatly reduces the heat transfer efficiency of the thermal oil boiler diesel burner, but also greatly increases the energy consumption cost, and it also leads to diesel combustion in the thermal oil boiler. The machine-corrosive metal corrodes and scales at high temperatures, the furnace tube metal is damaged by cracks or corroded holes, and the furnace tube can be burned in severe cases. The leakage of heat transfer oil may cause major accidents such as fire and human life. ! If you are interested in diesel combustion engines, please contact us for a quote!